Forum Post: AIX UNIX SERVER ISSUE
Hi, avocent. I have a question. I am using the DSView session is difficult to the AIX OS mouse settings. Using the mouse dual equally not synchronized. The target is connected to the MPU8032. Help me...
View ArticleWiki Page: RMA Check List (Key questions required before requesting RMA)
Issue:Appliance does not become ready to work after turning on.Resolution:Please make sure the following check list before raising RMA request. It is minimum requirement for general RMA request.If...
View ArticleForum Post: UMG cascading
Is it possible to cascade UMG with non-IP AutoView switches in similar manner like MPU with AV?Is it seamless?Do I need UMG dongles or only simple patch cables?
View ArticleForum Post: Visio stencils for TS-2000/3000
Ok ... no luck accessing the stencils that are available on the site and from 2005 ... who do I have to bride to get Visio stencils for my TS-2000 and TS-3000 terminal servers?
View ArticleForum Post: RE: Visio stencils for TS-2000/3000
Hello Sotek486; WEe do not have Visio stencils for the Very mature TS2000 / TS3000. I can get stencils for you of the ACS series... will that help?Regards; Danny
View ArticleForum Post: RE: DSR4030 can't launch KVM session Java message "Error" When...
Does Emerson/Avocent have plans to update the software to be compatible with Java p51 and beyond?
View ArticleForum Post: 4svdvi KVM switch not working with USB extension cables
We are trying to use USB extension cables (IOGEAR GUE2118) on the console keyboard and mouse ports. Both the keyboard and mouse are not working (they work fine without the extension cables). We've...
View ArticleForum Post: RE: 4svdvi KVM switch not working with USB extension cables
Thanks for the reply. Yes, I am aware that the (10m) extension cables exceed the official length for USB. However, there are many companies that manufacture "active" cables to overcome the length...
View ArticleForum Post: RE: how to Integrate Autoview KVM IP Switches into Dsview 3
Hello Nic; You cannot add the AV2015 into DSView management software. It does not even have KVM over IP capability;Regards;Danny
View ArticleForum Post: RE: Solution for PUE calculation for DC
[Update OLD Post]Please see the current information about Trellis Energy Insight with PUE and DCIE Dashboard at www.emersonnetworkpower.com/.../EnergyInsight.aspx
View ArticleForum Post: HMIQDHDD/HMX2050 won't pass resolution over 1440x900
I have a Dell Optiplex9010 with an NVIDIA NVS315 video card connected to a 1680x1050 monitor. Works fine.When I insert an HMIQDHDD/HMX2050 pair (1meter of CAT5), the highest res I can pass is...
View ArticleForum Post: RE: Welcome to the Emerson Network Power Support Community!
Avocent Longview LV830 n* de série: 0080109468 / MPN: 500-144-511Transmetteur : problème d'affichage VGA.(son + clavier + souris) fonctionnent.Acheté en France et je suis en Tunisie.Que peut être le...
View ArticleForum Post: RE: Loss of Communication Errors
Hello trev0422; Please bowse to this article and apply the suggestions community.emerson.com/.../948.minimizing-loss-of-communications-lcm-errors-in-dsview.aspxRegards;Danny
View ArticleForum Post: AV3016 - No power
I am trying to configure an AV3016.I connect the power, network and AVRIQ as directed.Only light I get is a blinking amber network light.I need to get an RMA or find out if I am out o warranty.SERIAL:...
View ArticleForum Post: RE: HMIQDHDD/HMX2050 won't pass resolution over 1440x900
Tom is correct you should upgrade the firmware on your Tx and Rx Also from the serial menu you want to check your EDID Preferred Timing in the Transmitter menu under the Advanced Video Settings Menu;...
View ArticleForum Post: RE: AV3016 - No power
Hello,It would be best to open a case with Technical Support for this.community.emerson.com/.../reqsuptKind regards,
View ArticleForum Post: MPU; What happend if the video-resolution of a server or...
Hello forum,We are contemplating buying an MPU and would like to know:What happend if the video-resolution of a server or workstation attached to a MPU does exceed the suppored resolution (of the MPU)?...
View ArticleForum Post: AMX 5030 Password
We had a 5030 cascaded to a 5000, the 5000 had a password on it. We no longer need the switches cascaded to we removed the 5030 and stored it, when we went to use again it asked for the password and...
View ArticleForum Post: RE: Problems with Keyboard and Mouse working with VMWare ESXi /...
Hi, mbevans. I also facing the issue now, do you solve this issue?
View Article