Forum Post: RE: CURRENT - Visio Stencils Cyclades ACS-48
Hello,Please open a case with us and we can large file transfer you the requested Visio stencils.community.emerson.com/.../supportRegards,SL
View ArticleForum Post: ACS 6000 Firmware 2.5.0.7 blanks Modem Init String
I've had two ACS 6000 with new 2.5.0.7 firmware applied to them, and when connecting the dial in line for out of band access to the devices, we've been unable to connect. It became apparent after...
View ArticleForum Post: Cyclades AlterPath KVM/net Cable Compatibility
I see from the manual located here:ftp://ftp.avocent.com/public/product-upgrades/cyclades/alterpath/kvmnet/doc/kvmnet_user_v211_050506.pdfon page 78 that the compatible cables are...
View ArticleForum Post: HMX2050 constant reboot
I have a HMX2050 and HMIQDHDD that go into a constant reboot loop, as soon as i plug DVI signal into the HMIQDHDD, if i just leave the usb and audio connected - it's finei have swapped out the TX &...
View ArticleForum Post: Autoview 1400 possword reset procedure
Hi,We lend our Autoview 1400 to a customer for an event.We didn't teated when he returned and a couple of month later we needed it, but now the OSD is promopting a password request.I tried to ask to...
View ArticleForum Post: DSView 4 on Linux: Able to change backups from being built in /tmp?
This for DSView 4. I've tested under versions 4.0.0.161 and 4.1.0.36. Basically, when the backup occurs it stores the temporary file it builds in the /tmp directory:[root@mkmbz4211 tmp]# ls -lah...
View ArticleForum Post: ACS32 - Upgrade not as successful as it said
I upgraded my ACS32 this afternoon through the GUI and it told me it was successful and I should reboot. When I rebooted the device (via the GUI), it never came back up and I get nothing in the...
View ArticleForum Post: RE: HMX2050 constant reboot
Is the firmware on all units the same? Is the resolution and refresh rate supported by the HMX ?Check power supply on all units, this could also be a problem when the power supply is dying you might...
View ArticleForum Post: RE: Switchview 1000 mouse problem
Hello Stefan,I've tried it with a PS/2 mouse connected to the switch and that seems to work fine. I've tried several USB Fujitsu mouses but on the bottom of the mouse there is the Logitech mark. Every...
View ArticleForum Post: RE: DSR2020 connect to a device gives Java exception
SOLVED: local firewall software on Windows was blocking Java.
View ArticleForum Post: RE: Autoview 1400 possword reset procedure
Hello Gatzu,Please open a Tech Support case for this and we can help you.community.emerson.com/.../reqsuptBest regards
View ArticleForum Post: RE: DSView 4 on Linux: Able to change backups from being built in...
Hi,As a bare minimum hardware requirement Dsview 4 should be installed on a Hard disk drive that has at least 40 GB of available space left after the Dsview install. Since Dsview is using the /tmp...
View ArticleForum Post: RE: Cyclades AlterPath KVM/net Cable Compatibility
Hello,No unfortunately the AVRIQ-PS2 modules are not compatible with the Altherpath KVM/net switches. They are only compatible with Avocent AutoView KVM switches.Best regards,
View ArticleForum Post: RE: Switchview 1000 mouse problem
Hello Stefan,Luckily I found another USB mouse somewhere in a drawer and it worked perfectly. I don't know for sure which brand it is. On the bottom of the mouse there is only a model name AMCOL and an...
View ArticleForum Post: RE: ACS6032 and Cisco 2811 compatibility?
Hi,we have the same problem with a Cisco1941 and ACS6048 now. Another Cisco1941 on a ACS6032 is running fineAny idea?Jens.
View ArticleForum Post: RE: ACS32 - Upgrade not as successful as it said
It would help if I was using the correct adapter! I was able to recover with the ADB0036
View ArticleForum Post: Disable SSH on Mergepoint Unity KVM switch?
Is it possible to disable the SSH server on the Mergepoint Unity KVM switch? I only have KVM devices on my switches... no serial consoles. I would like to disable the listening SSH (port 22).
View ArticleForum Post: DSView 4, scheduling appliance reboot?
Hi, all. Running the latest DSView 4 here. We've had some issues recently where our ASC6032s were not responding, and needed to be rebooted. Sometimes I've needed to apply a Firmware update via...
View Article