Forum Post: RE: Avocent Cyclades ACS48 48-Port Console Terminal Server
Hello Dave,Please try this recovery procedure:community.emerson.com/.../1196.acs-classic-fails-to-boot.aspx
View ArticleForum Post: RE: ACS60xx with Firmware 2.5.0.10 randomly freezes
Hello Martin,We haven't seen this behavior with ACS6000 on firmware version 2.5.0.10.You could try to factory default the ACS6000's that show this behavior. Verify if that resolves the issue. If it...
View ArticleForum Post: RE: Help configuring/setting up Avocent DSR8030
i have bought and used the recommend null cable and still no luckWhy did you guys choose to make it difficult to get into this device?Why use a special cable when you could have used same cable...
View ArticleForum Post: Visio stencils for ACS5008?
I see a number of unanswered posts from people looking for Visio stencils, so my hopes aren't high. Still, some time has gone by, and they might exist somewhere. Does anyone know where I can find...
View ArticleForum Post: RE: Visio stencils for ACS5008?
Hello MickeyU;Here is a link to VISIO stencils for the ACS product line. Â There is not a stencil for the ACS5008 so you will need to use a ACS6008 stencil.community.emerson.com/.../2245.aspxI hope this...
View ArticleForum Post: RE: cyclades alterpath sniff session configuration
To configure multiple sessions and port sniffing for one or more serial ports:1. Go to Ports - Physical Ports in Expert mode and select a port or ports to modify.2. Click the Multi User tab.3. To allow...
View ArticleForum Post: RE: ACS 5048 unable to upgrade
Good morning,has anyone any other ideas on that?
View ArticleForum Post: ts_menu show port numbers?
My group manages about 150 Cyclades, different models ranging from TS2000 to ACS48 to 6000 series, offering up consoles for different groups. Â Is there any way to modify ts_menu to show port numbers...
View ArticleForum Post: SC540 KVM issues
Hello,I have recently inherited a SiwtchView SC540 DVI switch. I have two problems:1. Logitech G5 mouse only moves in horizontal directions, regardless of which USB port it is plugged into2. I have...
View ArticleForum Post: HMX upgrade to 6.30.0.12
I successfully upgraded a HMX2050 from 6.10.0.11 to 6.30.0.12 using a stand alone pc with a xmodem serial connection to the hmx2050 unit. Â However I could not make an ethernet connection to a HMIQSHDI...
View ArticleForum Post: RE: ACS 5048 unable to upgrade
Hello,Try to upgrade with the firmware found here:www.avocent.com/.../ACS_5000_Advanced_Console_Servers.aspxThe File name is case sensitive, so the file name is: FL0588-008.binBest regards,Stefan Liedtke
View ArticleForum Post: RE: ts_menu show port numbers?
Hello,Unfortunately there is no way of doing that. Because it will always start with 1 due to the fact that you can have disabled ports on your ACS. So if you were to disable port 1 Ts_menu can't start...
View ArticleClik here to view.
Forum Post: RE: SC540 KVM issues
Hello,The Logitech G5 is a Gaming / Multimedia mouse and unfortunately these mice are not supported by this switch. Please connect a regular two button USB mouse. Your second issue is that your using a...
View ArticleForum Post: RE: Help configuring/setting up Avocent DSR8030
Hello,If you have a Null modem cable you should be able to access the console menu by using Hyper-Terminal or Putty with the following serial settings:9600 Baud8 Bits1 Stop BitNo parityNo Flow...
View ArticleForum Post: RE: What cable type between AutoView 3008 and AVRIQ?
Hello Mauro,So it sounds like you're seeing the OSCAR menu but when you try to connect to a port you only get a blank screen?Stefan
View ArticleForum Post: RE: lcd17swt16 - cable not connected
I would be more than happy too, but I'm sure these aren't covered under any type of warranty anymore. We've had them for quite a while. I'm wondering if the internal connection to the monitor is bad or...
View ArticleForum Post: RE: Avocent Cyclades ACS48 48-Port Console Terminal Server
You should use the ADB0036 console adapter with a straight trough Cat 5 patch cable.Regards,S. Liedtke
View ArticleForum Post: Loss of Audio from HMIQDHDD from target computer...
I have a HMX Manager(Hub&Spoke)and a bunch of HMX 2050 and HMIQDHDD appliances. Running version 6.30.0.14 on all devices and have an audio issue. Seems for no apparent reason we loose audio from a...
View ArticleForum Post: RE: HMX upgrade to 6.30.0.12
I see that you have a support case open for this matter through our support team, Please through the case, could you provide me with the SN# of that unit? Another questions to be checked up on, can you...
View ArticleForum Post: RE: How do I reset the login password in Avocent LCD17-001 ?
Maybe, The LCD17 need to be returned to factory for restet password.
View Article